This page is still in development - please check back soon for updates.
Note: in this Atlas, the word borehole is generally used to mean a drilled hole (by manual or mechanical rig), and the word well is generally used to mean a dug hole. Elsewhere, the word well is often used interchangeably with borehole to also mean a drilled hole.
There are two main approaches to drilling boreholes : drilling with a mechanised rig; and manual drilling. The most appropriate technique will depend on the hydrogeology, the required yield, and available funds.
An introduction to borehole drilling techniques that are appropriate for rural water supply can be found in the chapter Designing and constructing water points in MacDonald et al. (2001), which can be freely downloaded online.
Drilling with a rig
Most boreholes worldwide are drilled using a motorised drilling rig. There are different types of drilling rig and methods of drilling, and the most appropriate should be chosen to suit the local hydrogeological environment.
There are two main motorised drilling techniques: cable tool percussion (also known as shell and auger); and rotary drilling. Rotary is the most common method used for water borehole drilling. Rotary drilling can be air flush, sometimes with down-the-hole hammer; mud flush; or reverse circulation.
Manual drilling refers to several drilling methods that rely on human energy to construct a borehole. It is appropriate in some hydrogeological environments, where aquifers are shallow and unconsolidated (and therefore easier to drill through) and depth to groundwater (depth to the water table) is shallow. When done effectively, manual drilling can reduce drilling costs and increase cost-effectiveness of groundwater development programmes, compared to the costs of drilling using motorised rigs.
A separate Atlas resource page on manual drilling provides more information and resources.
Experienced supervision of drilling is essential for the provision of successful and long-lasting water boreholes.
The RWSN has produced a series of resources to support effective drilling supervision, including:
- - a guidance note on Supervising Water Well Drilling, which details the responsibilities of the drilling supervisor at different stages of borehole construction.
- - materials from a short training course on drilling supervision, which was delivered to engineers and WASH professionals in Sierra Leone.
Collecting Data during Drilling
Whichever drilling technique is used, collecting data during drilling is a very important part of successful groundwater development. Drilling is usually the only opportunity to look below the ground and find out what the geology and hydrogeology is at depth, where it is usually hidden. One of the main aims is to identify groundwater-production zones at depth in the geological sequence – at what depths is groundwater found? Data on the local geology is also invaluable for developing understanding. It is good practice for the drilling supervisor (see above) to collect data during drilling.
A good introduction to what data to collect during drilling, and how best to collect it, is in the chapter Designing and constructing water points in MacDonald et al. (2001), which can be freely downloaded online.
The activities in the table below are a summary of good practice in data collection during water borehole drilling.
|Activity||Why do this?|
|A field logbook or notebook should be kept, with notes of all drilling activities and what data are collected||Recording all information while in the field means that nothing is forgotten. A detailed field notebook is an invaluable record in case any details need to be checked later.|
|The borehole should be flushed clear of cuttings at the end of every sampling interval (e.g. every 1 m or every 3 m; or every drill rod) and an accurate sample of drill (rock) cuttings/chippings collected for observation.||Rock samples collected at depth during drilling provide a record of the geology and how it changes with depth. The geology is the main control on the groundwater potential.|
|Rock chip samples from the borehole should be washed and described consistently: e.g. rock type, colour, texture. In this way, a geological log is built up showing changes in geology with depth.||This allows people to assess where the best groundwater potential is with depth in the borehole, and therefore make the best decisions on the final borehole construction; and also to estimate how successful the borehole is likely to be. It also provides hugely valuable hydrogeological information to allow a wider assessment of groundwater resources beyond just one borehole.|
|Information should be recorded in the field logbook on: the penetration rate of drilling (how long it takes to drill a given interval, e.g. every 1 m or every drill rod); breaks or irregularities in drilling observed or reported by the driller; water strikes and/or flows; and dust production.||This information supports the description of geology in the geological log and helps improve understanding of the geology and the groundwater potential of the rocks.|
|If possible, water conductivity (SEC) should be measured at regular intervals/depths during drilling, to observe any changes.||Water conductivity indicates how mineralised a water is. If water conductivity changes suddenly, it can indicate that the borehole has entered a different aquifer with depth.|
|An initial estimate of potential borehole yield should be made during airlifting (cleaning the borehole) at the end of drilling.||This can help assess if the borehole is likely to be productive enough to be worthwhile installing screen and casing, and what size of pump to use for a pumping test.|
Professional Water Borehole Drilling
For successful and sustainable groundwater development, it is very important that borehole drilling is done in a professional way. Collecting data during drilling, as summarised above, is part of this, but it is a much bigger issue.
RWSN - Professionalising Borehole Drilling
The Rural Water Supply Network (RWSN) does much work to promote professional water borehole drilling. On its website you can view and freely download RWSN's resources, which have been used to improve projects and have been incorporated into the curricula of some academic and training organisations.
Some of the specific resources produced by RWSN to support professional water borehole drilling are:
- - A guidance note on Professional Water Well Drilling, available in English and in French / [http://www.rural-water-supply.net/en/resources/details/796 en français (Danert and Gesti-Canuto 2016). This is written for people who manage or support water borehole drilling programmes and projects, and provides guidance on project design, implementation and monitoring; groundwater information; capacity; institutional frameworks; investment; and dialogue and awareness.
- - A series of short animated films, in English and in French / en français. These films explain borehole siting, drilling supervision, drilling contract management and why some boreholes are better than others.
- - National assessments of the water borehole drilling sector (its cost-effectiveness and professionalism) for a number of countries, including at least 14 African countries.
- - A professional drilling management online training course, providing an introduction to the professional management of water borehole drilling projects and programmes.
There are a number of national or regional drilling associations in Africa, which work to improve professionalisation in the drilling sector, and improve the success and sustainability of water borehole drilling. Some of the most active of these associations are listed below:
- - The Borehole Water Association. The BWA is a membership organisation whose aim is to promote the sustainable use of Southern Africa's groundwater. It produces a journal - the Borehole Water Journal - with articles on groundwater issues, and useful advice for those looking to drill water boreholes.
- - The Association of Water Well Drilling Rig Owners & Practitioners (Borehole Drillers Association) of Nigeria is a membership organisation that aims to advance the professionalism of the drilling industry and support its members. Its website provides news relating to groundwater and directions to water borehole drilling services.
- - The Mozambique Drillers Association (Associação de Perfuração de Moçambique - APM) was established in 2006, with support from the World Bank. For a few years it actively worked to improve standards in the drilling sector in Mozambique, but it struggled to overcome the many challenges facing it, and it no longer has an active online presence. More information on its development and achievements, and some of the challenges, can be found in this Case Study.